Pixhawk 2.4.8 support the latest official ardupilot firmware and PX4 firmware.
1. The advanced 32-bit ARM CortexM4 high-performance processors(2MB flash), can run NuttX RTOS real-time operating system;
2. 14 PWM / servo output;
3. Bus interface (UART, I2C, SPI, CAN);
4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe;
5. Provide automatic and manual modes;
6. Provide redundant power input and failover;
7. Multicolor LED lights;
8. Provide multi-tone buzzer Interface
9. Micro SD recording flight data;
Specifications:
Interface
1 .5 high voltage compatible UART 1, 2 with hardware flow control
2. 2 CAN
3.Spektrum DSM / DSM2 / DSM-X satellite receiver compatible input
4.Futaba SBUS compatible inputs and outputs
5.PPM Signal Input
6.RSSI (PWM or voltage) Input
7.I2C
8.SPI
9.3.3 and 6.6VADC input
10. External MICRO USB Interface
TOP Package:
F450+4 PCS BLHELI 30A +4 pairs 1045 Propellers +4 PCS 2212 motor+Landing Gear
PIXHAWK 2.4.8(white or black shell)+ 4G TF Card + Safety Button + Buzzer + PPM Encoder + I2C Expansion Board+ RGB LED + OLED Screen+ 3 1.25 ,6Pin 1.25 ,3Pin 2.5.4) + M8N GPS+ GPS Holder+ 3DR Power Module+Shock Absorber+433MHZ V5 1000MW Radio telemetry+MINI OSD +PDB+VTX1000+1080P Camera
Frame 450:
BLHELI ESC:
A.Features
A1: Use authentic electronic components to ensure high quality and enhance the current endurance ability of the ESC.
A2: Based on BLHeli firmware, optimized for high performance with great and much quicker throttle response.
A3: Special designed for multirotors, and compatible with fixed-wing aircrafts and helicopters.
A4: Multiple protection features including Low-voltage cut-off protection / over-heat protection / throttle signal loss protection.
A5: Throttle range can be configured and is fully compatible with all receivers, providing smooth, and precise throttle response. A6: All parameters can be programmed via using a transmitter, including default settings.
B. Productspecification
2212 920KV Motor
1045 Propellers
M8N GPS:
Power Module
For PIXHAWK 2.4.8 :used for PIXHAWK2.4.8 AND APM2.8 Flight Control
For PIXHAWK PRO :used for PIXHAWK PRO Flight Control
For PIXHAWK 6C :used for PIXHAWK 6C Flight Control
Description:
This Power Module PRO provides a simple way to supply regulated 5.2V to flight controller from the battery while providing current consumption and battery voltage measurements via analog signal through a 6 Pin JST-GH cable. It comes with pre-soldered wires, capacitor, and XT60 connector on both ends, along with shrink tubing on the PCBA for physical protection.
Specification:
Input Voltage: 2S-12S
PCB Cont. Current Rating: 60A
PCB Burst Current Rating: 100A (<60 Sec)
Max Current Sensing: 120A
Output: DC 5.2V & 3A Max
Voltage Divider: 18.182
Amperes per Volt: 36.364
Weight: 20g
Please Note:
The XT60 Plug and 12AWG wire that are pre-soldered on the board is rating for 30A continuous current and 60A burst current (< 60 Seconds). If a higher current is being used, the plug type and wire size should be changed accordingly. You can refer to this chart for reference.
I2C:
PPM:
RGB:
The powerful features of Pixhawk are self-evident. Its integrated RGB full color multifunctional indicator light has high brightness, making it easy to identify flight control status. Compared to previous APMs, it is more intuitive and clear, making it a great design. But the problem lies here: this RGB LED is facing upwards and can only be viewed on the ground, unable to recognize flight control status in the air. Additionally, some racks have a fully enclosed design, such as the SKY-HERO, where the flight control can be hidden between two central boards, making it difficult for users to easily connect USB cables while being well protected. So we referred to the official accessory design and launched this two in one Pixhawk RGB module.
The Pixhawk RGB module has the following characteristics:
·Extend the RGB indicator light to the exterior of the aircraft to display;
·Extend the USB port to facilitate external connection to the USB cable, without being limited by the flight control installation location;
·The Toshiba LED controller and Osram\'s RGB high brightness LED are identical to those on the Pixhawk board;
·Molex original 1.25 connector and HRS original USB socket ensure good contact stability.
Use OLED for PIXHAWK, must follow these steps,
Connect OLED to I2C port of Pixhawk
Upload ardupilot firmware, at least 3.5 version, below 3.5 version will not be display.
Use Mission Planner to modify parameters NTF_DISPLAY_TYPE to 1. After modify, remember to click “Write Params” button.
Now the OLED is only supported for ardupilot firmware,can not be supported PX4 firmware
Reboot the board.
Radio telemetry V5
MINI OSD:
PDB:
VTX1000 is video transmitter,support 25MW-600MW,48 channel (with heat sink abd 3DBantenna)
Description:
Model: MINI MS-1672 FPV cameras
?Sensor: 1/1/8 \"CMOS D1080H
?Horizontal resolution: 2000TVL
?Horizontal field of view: 165
?Lens: 2.1mm lens
?Video format: NTC&PAL (adjustable)
?Image scale: 4:3&16:9 (automatic recognition)
?Wide Dynamic Range: Super WDR
?Noise reduction: 3DNR
?Low illumination: 0.001LUX
?Video output: CVBS
?Day and night: external/internal/black and white/color
?Language: (English/Chinese/Traditional Chinese/pyccnna)
?ESOABIK/TTASSNO/FRABCAUS/
?POSDIM/PORTUGUES/Japanese
?Electronic Shutter: PAL: 1/50-100000NTSC: 1/60-100000
?Wide voltage input: 5-36V
?Working temperature: -20-60
?Weight: 110g
?Dimensions: 19 19 19mm
?Resolution: 960 * 1080
?
?Feature:
?Upgraded Mista 2000TVL 2.1mm Wide Angle HD 1080P CCD PAL/NTSC Switchable 16:9 OSD FPV Camera.
?
?Package included:
?1 x Upgraded Mista FPV Camera
商品備註・物品狀況:全新・最新關注時間:2026-10-17